Main Menu
Your Cart

Naraku Compression Spring 1000 RPM (DIO, GET, QMB)

Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)

Description: Naraku Compression Spring aka torque spring does a couple of things. First, they supply the pressure to engage the belt. They also determine the rate at which the CVT transmission changes from low to high gear. A 1000rpm spring will go into a higher gear than a 2000rpm spring. Markings on the spring help you identify the strength of the spring, for example, a spring marked 1000 RPM will delay the reaction by 1000 RPM. The greater RPM spring will provide you with greater power. Naraku counter pressure spring 1000 RPM uses a modified alloy spring providing better resilience and above-average strength for 139QMB, Buddy50, RoughHouse, and many other GY6 50cc base engines.

Compatible with sport clutches on the market works on Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft lbs. For reassurance please consult your manufacturer variator torque specs.

Specifications:

Include the following Compression spring.

•    1x Spring Comp: 1,500 RPM / L: 106mm
•    Spring ID: 48.5mm / OD: 58mm
•    Wire Gauge: 4mm
•    Made in Taiwan
•    Fit Belt Size: 654 (Fit DIO ONLY)
•    Fit Belt Size: 660785 (Fit GET ONLY)
•    Fit Belt Size: 669, 729, 788 (Fit QMB ONLY)
•    Fit Dowel Pin Set (8x14mm)
•    Fit DIO 49/90cc+
•    Fit GET 49/50cc
•    Fit QMB 49/50cc+

Supported Models: Naraku CVT Kit (Part# KIT.A.139QMB); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

-----
Item Weight & Product Dimensions:
•   0.181 Pounds | 4.173" (L) x 2.283" (W) x 1.909" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
Naraku Compression Spring 1000 RPM (DIO, GET, QMB)
  • Stock: 1
  • Part #: NK900.63
Sold: 7
Views: 17206
$14.95
Price in reward points: 15

Included