Main Menu
Your Cart

NCY Drive Face 114mm CNC-Machined Alumin (GY6)

NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
NCY Drive Face 114mm CNC-Machined Alumin (GY6)

Description: High-quality CNC machined aluminum drive face 114mm by NCY for the GY6 125/150cc+ scooters. The CNC-machined running surface of the disc allows for a clean, low-vibration belt operation. Not to mention its kool spectrum of silver, brass, and rose gold - color streaks!

Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

NOTE: THIS IS NOT FOR Honda PCX (See Part# 1200-1193). GY6 engine, ankle-biter, clutch bell, and starter motor - not included, sold separately. Caution must be taken when using this product! This is intended for show purposes/off-road use only and should not be used on a public road or highway! You are responsible for any damage this product may cause to you personally or any other objects/personal property.

Specifications:

•    1x Aluminum CNC Machined Anodized Drive Face Weight: 144.7gm
•    Splines: 19 / ID: 13.5mm / OD: 114mm / H: 10<13.55mm
•    Made in Taiwan
•    Fit Variator Housing: 114mm or 115mm / Weights: 18x14mm / Slides: 3 Top: 87mm / Boss: 24mm / Shims: 24mm
    Fit Variator/Clutch Shaft Nuts: M12 / Washers: M12 / Socket: 17mm
•    Fit Belt Size: 743835842-20-30
•    Fit Dowel Pin Set (8x10mm)
•    Fit GY6 125/150cc+

Supported Models: NCY CVT KIT (Part #1200-1048); GY6 152QMI 157QMJ 161QMK 161QML Chinese Scooter, ATV, Genuine Buddy, Kymco, Ruckus, Vento

-----
Item Weight & Product Dimensions:
•    0.319 pounds | 4.488" (OD) x 5.31" (ID) x 0.533" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
NCY Drive Face 114mm CNC-Machined Alumin (GY6)
  • Stock: 34
  • Reward Points: 1
  • Part #: 1200-1021
Sold: 80
Views: 15560
$31.00
Price in reward points: 31

Included