Main Menu
Your Cart

NCY Secondary Slider Pin Set (DIO, GET, QMB)

NCY Secondary Slider Pin Set (DIO, GET, QMB)
NCY Secondary Slider Pin Set (DIO, GET, QMB)
NCY Secondary Slider Pin Set (DIO, GET, QMB)
NCY Secondary Slider Pin Set (DIO, GET, QMB)
NCY Secondary Slider Pin Set (DIO, GET, QMB)
NCY Secondary Slider Pin Set (DIO, GET, QMB)

Description: NCY Secondary Slider Pin Set. Some rear pulley shaft may come with larger slider pins aka "guiding pins", if so, these 6mm outer-diameter guiding pins will be needed to replace larger guiding pins to fit secondary slider securely onto rear pulley shaft. Made for 139QMB 49cc-50cc 4-stroke GY6 50 engine based scooters, ATVs, and off-road karts. Also, fit Honda Dio/Elite and Honda GET only with conversion secondary pulley assembly. The set includes 3 slider pins.

NOTE: Before use, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.


Include the following Slider pin set.

•    3x Secondary Slider Pins L: 9.3<10.86mm / ID: 5mm / OD: 6mm
•    Made in Taiwan
•    Fit Clutch Nut: M28 / Socket: 39mm
    Fit Clutch: 105mm / Shaft Slider: 33.5mm / Nut: M10 / Washer: M10 / Bearing Seat47.4mm / Bell Spline: 22 Socket: 14mm
•    Fit Belt Size: 
660-18-28785-18-30 (Fit GET ONLY)
•    Fit Belt Size: 669729, 788-18-30 (Fit QMB ONLY)
•    Fit Belt Size: 654669-18-30 (Fit DIO ONLY)
•    Fit Compression Spring: 1k1.5k2k rpm
•    Fit Clutch Springs: 1k1.5k2k rpm
•    Fit Dowel Pin Set (8x10mm)
•    Fit DIO 49/90cc+
•    Fit GET 49/50cc
•    Fit QMB 49/50cc+

Supported Models: NCY CVT Kit (Part# 1200-1171); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

Item Weight & Product Dimensions:
•    0.06 pounds | 0.427" (L) x 0.196" (ID) x 0.236" (OD)

Sorry, this video is NOT dubbed in English. Khmer speaking only.

Write a review

Note: HTML is not translated!
Bad Good
NCY Secondary Slider Pin Set (DIO, GET, QMB)
  • Stock: 22
  • Part #: 1200-1268-P
Sold: 11
Views: 1885
Price in reward points: 15