NCY Variator 89mm Coated Gold (DIO, QMB)
Description: The ultimate variator for your 139QMB and DIO transmission! This beauty is lighter than any other variator on the market weight at 17.3oz and an 89mm outer diameter drive face is ideal for all types of riding. The teflon coated roller tracks prevent debris accumulation that causes roller weights to a flat spot, leading to extended roller weight life and consistently smooth transitions.
This is one of the most versatile and compatible sports variator on the market works on Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, and virtually any scooter engine with these measurements.
NOTE: NCY Variator Ramp Top (Sold Separately, Part# 1200-1056). Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply blue Loctite, torque when assembling. For Honda DIO require belt-size 654-18-30 (Part# BD44DIO-6541830).
Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
Include the following Variator housing.
• 1x Alumin-Alloy Housing Teflon Coated ID: 20mm / OD: 89mm / H: 32.44mm
• Made in Taiwan
• Fit Starter: Bendix / Lock: Bracket
• Fit Variator Weights: 16x13mm / Slides: 3 / Top: 73.5mm / Boss: 20mm / Shims: 20mm
• Fit Variator Shaft Nut: M12 / Washer: M12 / Socket: 17mm
• Fit Belt Size: 669, 729, 788-18-30 (Fit QMB ONLY)
• Fit Belt Size: 654, 669-18-30 (Fit DIO ONLY)
• Fit Dowel Pin Set (8x10mm)
• Fit DIO 49/90cc+
• Fit QMB 49/50cc+
Supported Models: NCY CVT Kit (Part# 1200-1171); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, and virtually any scooter engine with these measurements.
Item Weight & Product Dimensions:
• 0.338 pounds | 3.505" (OD) x 3.202" (ID) x 1.288" (H)