SSP-G CVT KIT (139QMB, Buddy, RoughHouse)
Description: SSP-G CVT Kit 139QMB aka Super CVT transmission kit for GY6 50cc engines is one of the best dollar-for-dollar bolt-on to improve your 139QMB, Buddy50, or RoughHouse scooter! Quicker acceleration, reach faster top speeds, and makes your 139QMB CVT the smoothest running transmission in town! From rapid downshifting to slow cruising, this thing is smooth. Ultralight balanced components, oversized wear pads, and state-of-the-art polytetrafluoroethylene (PTFE) coatings ensure superior performance and long service life.
NOTE: Some rear pulley shaft may come with larger slider pins aka "guiding pins", if so, 6mm O.D. guiding pins will be needed to replace larger guiding pins, see Part# 151-148 (sold separately). Must re-use stock variator boss, variator fan overlay, washers, rear pulley plate shaft, slider pins, slider seat funnel, clutch nut, and nuts. If installing on a Genuine Buddy 50 or RoughHouse 50 must re-use the drive face and belt-size 738-18-30 (sold separately). Most parts also will fit Honda DIO's CVT. Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.
Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
Specifications:100% SSP-G Products – OPTIONAL ADD-ON (IN RED).
1. Includes SSP-G Drive Face Aluminum, Drive Face, and Kickstart him.
• 1x Drive Face ID: 13.5mm (Splines 26) / OD: 112.3mm (Teeth 63) / H: 4.2<13.5mm
• 1x Stainless Steel Kickstart Him ID: 13.5mm (Splines 26) / OD: 34.32mm / H: 4<7.3mm
2. Includes SSP-G Variator 88mm, Roller weights, Variator housing, Variator slides, and Variator top.
• 1x Alumin-Alloy Housing ID: 20mm / OD: 89mm / H: 32.44mm
• 1x Metal Top ID: 14.15mm / OD: 73.50mm / H: 11.58mm
• 6x Roller Weights (black): 16x13 8gm
• 3x Plastic Slides (black)
3. Includes SSP-G Secondary Slider, slider (torque driver), and O-rings.
• 1x Secondary Slider Plate OD: 119mm / Funnel ID: 33.5mm / OD: 43mm / H: 32.70mm (Make Selection)
• 2x Rubber O-rings
4. Include SSP-G Compression Spring 1500 RPM, Compression spring. (Make Selection)
• 1x Spring Comp (yellow): 1500 RPM / L: 105mm
• Spring ID: 49mm / OD: 57.8mm
• Wire Gauge: 4mm
5. Includes SSP-G Clutch Performance, Clutch housing, Clutch springs, and Clutch weights.
• 1x Clutch ID: 24<28mm / OD: 105mm / H: 29.55mm
• 3x Clutch Springs (blue): 1000 RPM (Make Selection)
• 3x Clutch Weights (gray)
6. Include SSP-G Clutch Bell, Clutch bell.
• 1x Iron Clutch Bell Vented ID: 107mm / OD: 118mm / H: 34.54mm
• Splines: 22 / ID: 11.10mm / OD: 16.95mm / H: 17.75mm
• Made in Taiwan
• Fit Starter: Bendix / Lock: Bracket
• Fit Clutch Nut: M28 / Socket: 39mm
• Fit Clutch Shaft Pins: 6mm / Nut: M10 / Washer: M10 / Bearing Funnel: 43mm / Socket: 14mm
• Fit Variator Fan: Overlay / Ratchet: Gear / Shaft Nut: M12 / Washer: M12 / Boss: 20mm / Shims: 20mm / Socket: 17mm
• Fit Belt Size: 669, 729, 788-18-30 (Fit 139QMB ONLY)
• Fit Belt Size: 738-18-30 (Fit RoughHouse ONLY)
• Fit Clutch Springs: 1k, 1.5k, 2k rpm
• Fit Compression Spring: 1k, 2k rpm
• Fit Crankshaft 41.4mm to 44mm
• Fit Dowel Pin Set (8x10mm)
• Fit QMB 49/50cc+
Supported Models: Naraku CVT Kit (Part# KIT.A.139QMB); 139QMB 49cc-50cc engines, Baja SC50, Boreem (BMS) 50, Buddy50, Filly 50, Kymco 50, Panterra 50, Peugeot 50, Piaggio 50, Qingqi 50, QLink 50, Roketa 50, RoughHouse 50, SUNL 50, SYM 50, Tank 50, TaoTao 50, and virtually any other scooter engine with these measurements.
Item Weight & Package Dimensions:
• 3.862 pounds | 17.5” (L) x 6.4” (W) x 5” (H)
From Same Category
- Stock: 39
- Reward Points: 6
- Part #: 169-197