SSP-G CVT KIT (GY6) - CUSTOMIZABLE
NOTE: THIS KIT IS NOT FOR Honda PCX (See Part# 1200-1195). Must re-use washers, rear pulley plate shaft, slider pins, clutch nut, and nuts. For some models like the Polaris RZR 170, you'll need to widen the SSP-G Variator Top plate center hole, with a dremel tool, to fit through its variator shaft. Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.
Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
SSP-G CVT KIT (GY6) – SEVEN CUSTOMIZABLES.
Includes the following Drive face, Roller weights, Variator, Secondary slider, Springs, Spring bearing seat, Clutch, and Clutch bell.
1. Include Drive Face, Drive Face. (Make Selection)
• 1x Aluminum Drive Face Fan/CNC Weight: 144.7<157gm / OD: 115mm / H: 18<21mm
• Splines: 19 / ID: 13.5<15mm / H: 7mm
2. Includes SSP-G Variator 115mm Set, Roller weights, Variator housing, Variator slides, Variator Boss, and Variator top.
• 1x Alumin-Alloy Housing ID: 24mm / OD: 114.6mm / H: 36mm (Make Selection)
• 1x Stainless Steel Boss L: 51.54mm / ID: 15mm / OD: 23.94mm / W: 107.7gm
• 1x Metal Top ID: 15.2mm / OD: 86mm / H: 24mm
• 6x Roller Weights (red): 18x14mm 10<12gm (Make Selection)
• 3x Plastic Slides (white)
3. Includes SSP-G Secondary Slider, slider (torque driver), and O-rings.
• 1x Secondary Slider Plate OD: 142mm / Funnel ID: 34mm / OD: 43mm / H: 47mm (Make Selection)
• 2x Rubber O-rings
4. Includes Secondary Bearing Spring Seat, Bearings, and Bearing seat. (Make Selection)
• 1x Bearing Seat ID: 45.4mm / OD: 57.5mm / H: 3mm / Grove: 1.75mm
• 1x Bearings Pak
5. Include Compression Spring, Compression spring.
• 1x Spring Comp: 1k<2k RPM / L: 114<154mm (Make Selection)
• Spring ID: 48.5mm / OD: 58<58.5mm
• Wire Gauge: 4.2<4.56mm
6. Includes SSP-G Clutch Performance, Clutch housing, Clutch springs, and Clutch weights.
• 1x Clutch ID: 24.3<28mm / OD: 119mm / H: 35.4mm
• 3x Clutch Springs (blue): 1000 RPM
• 3x Clutch Weights (red)
7. Include Clutch Bell Racing Star, Clutch bell. (Make Selection)
• 1x Iron Clutch Bell Star Vented (10-Spokes) Weight: 680.39<717.24gm / ID: 125mm / OD: 137mm / H: 43.3mm
• Splines: 19 / ID: 13.5<15mm / OD: 20mm / H: 24.3mm
• Made in Taiwan
• Fit Variator Boss Shims: 24mm / Nut: M12 / Washer: M12
• Fit Clutch Shaft: 174mm / Sheave: 34mm / Nuts: M12, M28 / Washer: M12 / Bearing Seat: 45.4mm / Socket: 17mm, 39mm
• Fit Compression Spring: 1k, 1.5k, 2k rpm
• Fit Clutch Springs: 1k, 1.5k, 2k rpm
• Fit Belt Size: 743, 835, 842-20-30
• Fit Dowel Pin Set (8x10mm)
• Fit GY6 125/150cc+
Supported Models: Ban Jing CVT KIT (Part# 169-500); GY6 152QMI 157QMJ 161QMK 161QML Chinese Scooter, ATV, Genuine Buddy, Kymco, Polaris RZR 170, Ruckus GY6 Swap, Vento
Item Weight & Package Dimensions:
• 6.731 pounds | 10.25” (L) x 7” (W) x 6” (H)
From Same Category
- Stock: 37
- Reward Points: 8
- Part #: 169-530