Main Menu
Your Cart

Stage6 Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)

Stage6 Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
Stage6 Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
Stage6 Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
Stage6 Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)

Description: Stage6 Variator Roller Weight Tuning Kit 16x13mm for Honda DIO/Elite, GET, and 139QMB 4-stroke engines. The set consists of 4x6 cores and shells made of very wear-resistant plastic that is not affected by temperature changes. The shells are of course also available as spare parts. For better identification, the individual rollers have the weight printed on them, so mixing them up (as it can happen with other sets) becomes impossible. The set comes in a shatter-proof box.

NOTE: You must install these weights in an alternating pattern, otherwise a severe imbalance in the variator will occur. These rollers are designed for tuning purposes only and we recommend that they are not used for long-term use. Once you have determined the appropriate weight for your set up you should buy a complete roller set for permanent use.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

NOTE: You must install these weights in an alternating pattern, otherwise a severe imbalance in the variator will occur. These rollers are designed for tuning purposes only and we recommend that they are not used for long-term use. Once you have determined the appropriate weight for your set up you should buy a complete roller set for permanent use.

Specifications:

Includes the following Roller weights and Shell set.

•    12x Wear-Resistant Plastic Shell Size: 16x13mm
•    24x Brass-Gold Core Weights (choose set): 4/ech. 6 core weights
•    1x Plastic Compartment Case
•    Made in Italy
•    Fit Variator Housing: 88mm89mm or 95mm Slides: 3 / Boss: 20mm / Shims: 20mm
    Fit Variator Shaft Nut: M12 / Washer: M12 / Socket: 17mm
•    Fit Belt Size: 654669-18-30 (Fit DIO ONLY)
•    Fit Belt Size: 660-18-28 (Fit Metro ONLY)
•    Fit Belt Size: 785-18-30 (Fit Ruckus ONLY)
•    Fit Belt Size: 669, 729, 788-18-30 (Fit QMB ONLY)
•    Fit Dowel Pin Set (8x10mm)
•    Fit DIO 49/90cc+
•    Fit GET 49/50cc
•    Fit QMB 49/50cc+

Supported Models: Naraku CVT Kit (Part# KIT.A.139QMB); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly50, Kymco, MetropolitanGET, QLink, Peugeot, Piaggio, RoughHouse, RuckusGET, SYM, TaoTao, and virtually any scooter engine with these measurements.

-----
Item Weight & Package Dimensions:
•    0.35 pounds | 6.5" (L) x 2.6" (W) x 0.75" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
Stage6 Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
  • Stock: 36
  • Reward Points: 1
  • Part #: S6-GS16011
Sold: 4
Views: 3317
$39.95
Price in reward points: 34

Included