Main Menu
Your Cart

TFC Variator 114mm Coated w/Comp Spring Kit (GY6)

TFC Variator 114mm Coated w/Comp Spring Kit (GY6)
TFC Variator 114mm Coated w/Comp Spring Kit (GY6)
TFC Variator 114mm Coated w/Comp Spring Kit (GY6)
TFC Variator 114mm Coated w/Comp Spring Kit (GY6)

Description: TFC products are some of the best on the market today! This racing variator from TFC is precision-engineered to increase performance over stock GY6 variators. The steep angle ramp plates in the TFC Variators allow for a faster and smoother engagement at all speeds, allowing lighter weighted sliders to fully extend to make the most of your CVT system. The TFC GY6 Variator comes with the variator, fan plate, washers, Sliders, and set of 18x14 weights in 12 grams rollers. This will also work on the Polaris RZR 170.

NOTE: Some models like the Polaris RZR 170 you'll need to widen the TFC Variator Top plate center hole, with a dremel tool, to fit through its variator shaft. Recommend using a new belt with this kit. Belt and the belt drive facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling.

Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft lbs. For reassurance please consult your manufacturer variator torque specs.

Specifications:

Includes the following Variator nut, Variator drive face, Variator housing, Variator slides, Variator top, Rollers, and washers.

•    1x Alumin-Alloy Eloctroplated Drive Face Fan ID: 14<15mm / Splines: 19 / OD: 114mm / H: 18mm
•    1x Alumin-Alloy Housing Teflon Coated ID: 24mm / OD: 114mm / H: 36mm
•    9x Roller Weights: 18x14mm 12gm
•    1x Metal Top ID: 15mm / OD: 86.9mm / H: 22mm
•    1x Compression Spring
•    3x Plastic Tan Slides
•    2x Metal Washers
•    1x Variator Nut
•    Made in Taiwan
•    Fit Roller Weights: 18x14mm
•    Fit Belt Size: 743835842
•    Fit Boss ID: 15mm / OD: 24mm
•    Fit Dowel Pin Set (8x14mm)
•    Fit 54mm Stud Spacing (A-Block)
•    Fit 57mm Stud Spacing (B-Block)
•    Fit GY6 125/150cc+

Supported Models: NCY CVT KIT (Part# 1200-1048-1); GY6 152QMI 157QMJ 161QMK 161QML Chinese Scooter, ATV, Genuine Buddy, Kymco, Polaris RZR 170, Ruckus, Vento

-----
Item Weight & Product Dimensions:
•    1.106 pounds | 4.528" (L) x 4.528" (W) x 2.968" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
TFC Variator 114mm Coated w/Comp Spring Kit (GY6)
  • Stock: 40
  • Reward Points: 6
  • Part #: TFC-012
Sold: 0
Views: 467
$159.00
Price in reward points: 159

Included