SSP-G Clutch Kit Adjustable (139QMB, Buddy, RoughHouse)
Description: SSP-G Clutch Kit Adjustable for 139QMB 49/50cc 4-stroke engines. It is one of the best dollar-for-dollar bolt-on to improve your 139QMB, Buddy50, or RoughHouse scooter! Quicker acceleration, reach faster top speeds, and makes your 139QMB CVT the smoothest running transmission in town! From rapid downshifting to slow cruising, this thing is smooth. Ultralight balanced components, oversized wear pads, and state-of-the-art polytetrafluoroethylene (PTFE) coatings ensure superior performance and long service life.
NOTE: If installing on a Genuine Buddy 50 or RoughHouse 50 must re-use the drive face and belt-size 738-18-30 (sold separately). Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Must re-use stock variator assembly, variator fan, fan overlay, and washers. RoughHouse must re-use the drive face and belt-size 738-18-30 (sold separately). Most parts also will fit Honda DIO's CVT.
Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
SSP-G Clutch Kit (139QMB, Buddy, RoughHouse) – OPTIONAL ADD-ON (IN RED).
1. Includes SSP-G Secondary Sliding Sheave Assembly, slider (torque driver), O-rings, and clutch nut.
• 1x Rear Pulley Shaft ID: 17.43<21mm / OD: 34<45.1mm / H: 68.73mm
• 1x Rear Pulley Plate OD: 119mm
• 3x Secondary Slider Guides
• 3x Secondary Slider Pins OD: 6mm
• 1x Secondary Slider Funnel ID: 33.5mm / OD: 43mm / H: 32.70mm
• 1x Secondary Slider Plate OD: 119mm
• 1x Secondary Spring Seat/Funnel ID: 43mm / OD: 45<61mm / H: 30mm
• 1x Stainless Steel Clutch Nut: M28
2. Include SSP-G Compression Spring 1500 RPM, Compression spring.
• 1x Spring Comp (green): 1500 RPM / L: 105mm
• Spring ID: 49mm / OD: 57.8mm
• Wire Gauge: 4mm
3. Includes SSP-G Clutch Performance Adjustable, Clutch housing, and Clutch springs.
• 1x Clutch ID: 24.3<28mm / OD: 104.6mm / H: 30mm
• 3x Clutch Springs: 1500 RPM
• 3x Clutch Weights (gray)
4. Include SSP-G Clutch Bell, Clutch bell.
• 1x Iron Clutch Bell ID: 107mm / OD: 118mm / H: 34.54mm
• Splines: 22 / ID: 11<12mm / OD: 1mm / H: 17.75mm
• Bearing: 6901 RS
• Made in Taiwan
• Fit Starter: Bendix / Lock: Bracket
• Fit Clutch Shaft: 155mm Nut: M10 / Washer: M10 / Bearing Funnel: 43mm / Socket: 14mm, 39mm
• Fit Belt Size: 669, 729, 788-18-30 (Fit 139QMB ONLY)
• Fit Belt Size: 738-18-30 (Fit RoughHouse ONLY)
• Fit Compression Spring: 1k, 1.5k, 2k rpm
• Fit Clutch Springs: 1k, 1.5k, 2k rpm
• Fit Dowel Pin Set (8x10mm)
• Fit QMB 49/50cc+
Supported Models: SSP-G CVT Kit (Part# 169-197); 139QMB 49cc-50cc engines, Baja SC50, Boreem (BMS) 50, Buddy50, Filly 50, Kymco 50, Panterra 50, Peugeot 50, Piaggio 50, Qingqi 50, QLink 50, Roketa 50, RoughHouse 50, SUNL 50, SYM 50, Tank 50, TaoTao 50, and virtually any other scooter engine with these measurements.
Item Weight & Package Dimensions:
• 2.562 pounds | 8” (L) x 6.4” (W) x 5” (H)
From Same Category
- Stock: 40
- Reward Points: 4
- Part #: 169-171